MACHINIST TOOL

HERE IS THE BEST MACHINIST TOOL FOR
MARKING METAL DIES, MOLDS, TOOLS, PARTS, AND
EQUIPMENT WITH NAMES, NUMBERS, DESIGNS, OR TRADEMARKS  IN SECONDS
FOR LESS THAN ONE CENT PER MARK.

Here Is The Machinist Tool For Metal Marking That You Can Easily
Use In Your Own Shop To Mark Anything Metal In Just Seconds!
Now All You Do Is Create Your Own Design, Logo, Brand Name 
Or Trademark And Then Use the Etch-O-Matic To Put It On Your 
Tools, Parts Or Equipment For Less Than A Cent Per Mark.
  It Is Easy, Quick, Inexpensive And Professional! 
 And YOU Can Do It!
 HERE IS WHAT YOUR MARKS WILL LOOK LIKE!

Etch Trademarks

Etch Black On 1/4" Drill Bit 

Acid Etch Deep Marks 

Black Marks In Seconds

Etch Your Tools & Gauges

Deep Etch BLACK Mark


HERE IS HOW TO MARK ANYTHING METAL
 Using Dura-Film Stencils And 
The Etch-O-Matic Machinist Tool Kit.
Here Is The Quick, Easy And Inexpensive Way To Mark Your Dies, Tools, Parts Or Even A Knife.

First Make Your Artwork On Your Computer With Our New Ultra Violet Stencil-Makers.  When Finished It Should Look Like This One. Or You Can Use Our Regular Die Impressed Stencils Which Are Included In Every Kit By Simply Typing On Them.

Next Place The Stencil On Your Die, Mold, Tool, Part Or Knife Blade
And Use A Small Piece Of Scotch Tape To Hold It In Position. 

When Ready Wet The Head Of The Etch-O-Matic With Electrolyte And Place It On The Stencil.  After Everything Is Lined Up Correctly Just Touch The Blade With The Ground Wire 
(Shown With Alligator Clip) For A Few Seconds And Your Mark Is Complete.

Here Is Your Mark.  It Is Black On Stainless Steel But You Can Also Make 
Deep Etch Marks Down To About .003" And They Can Be "Clear" Or Black.

Now You Can See Just How Easy It Is To Put Your Own Mark On
Anything Metal Including Tools, Parts, Instruments Or Even Knives.

HERE IS HOW THE ETCH-O-MATIC MACHINIST TOOL KIT WORKS!

REGULAR MARKING

MARKING WITH GROUND PLATE — Simply Lay the Tool or Part on the Ground Plate and Touch ETCH-O-MATIC to it for a Few Brief Seconds and Your Mark is Chemically Etched Into Your Tool.

ETCHING ROUND SURFACES

MARKING ROUND SURFACES — Drill Bits, Milling Cutters, Tubing, Pipe or nearly anything Round can be Easily Marked by "Rolling"  the Mark on as Shown Above.

DEEP ETCH MARKING

MAKES DEEP ETCH MARKS— ETCH-O- MATIC Marks many Metals as Deep as .003" with Deep Etch Adapter Clip, a Mark that can only be Removed by Grinding a Major Part of the Surface Away.

 

 

      If it is Made of Metal
        ETCH-O-MATIC
    Can Mark It And Even
               Put Your
          TRADEMARK
    On It In Just Seconds!

 



MACHINIST TOOL TO PERMANENTLY 
MARK ANYTHING METAL
....IN SECONDS!

ETCHES MARK INTO SURFACE — The ETCH-O-MATIC Machinist Tool Kit will Chemically Etch into the Surface of Anything made of Metal, including Tools, Instruments, Equipment or Manufactured Parts, anything that can be Typed, Written, Drawn or Photo Processed on a Special Stencil. This includes Names, Numbers, Designs, Logos, Trademarks or even Your Own Signature. Using an Electro- Chemical Principle, the New ETCH-O-MATIC can Etch as Deep as .003" of an Inch in Less than 30 Seconds or Mark the Hardest Tool Steel and Carbides Almost Instantly. It marks any Flat or Round Metal Surface down to 1/16" Diameter and any Metal Thickness from Thin Foil up to the Largest Castings easily. Most Marks (which look like Printing or Engraving) take about 3 to 20 Seconds (the Longer Dwell Times are for Deep Etching) and are Permanently Etched into the Tool or Manufactured Part.

 

FAST AND VERY EASY TO USE!

 

ETCH-O-MATIC is FAST and EASY TO USE. Anyone in Your Organization can Become an EXPERT in JUST MINUTES and Produce Professional Looking Marks Quickly. In Fact, Etch-O-Matic is by Far the Very Easiest Marking System to Learn that is Available Today!  Also, You will find that ETCH-O-MATIC is not only the Fastest way to make Permanent Marks on Anything Metal, but is by Far the LEAST EXPENSIVE method on the Market Today. Your Marks will Cost just Fractions of a Cent to Produce and You will be Extremely Pleased with the Result.

 

                               RESULTS LOOK LIKE LASER MARKS

 

Most Marks will Compare Favorably with Laser Marking on Metal and are Easier and Sometimes Even Faster to Make.  In Fact You have Seen Marks made by Etch-O-Matic hundreds of times before but probably did Not Realize it since the Marks are Used so often in Commerce Today.  If you have ever seen a Feeler Gauge, Drill Bit, Milling Cutter, Saw Blade, Knife Blade, Ball Bearing Race, Carbide Cutter or Thousands of other types of Metal Tools, Parts, Instruments or Equipment then You have probably seen Marks made by Etch-O-Matic.  In fact, we have Marks in a good Percentage of all of the Cars, Trucks, Commercial and Military Aircraft, Submarines, Hospital Surgical Instruments and Implant Devices. We Even have Marks in the Nose Cone of the Space Shuttle.  (Yes, NASA called and said that they used an Etch-O-Matic to Mark an Inspection Date and Number in the Nose Cone of the Space Shuttles.)

 

BASICALLY, ETCH-O-MATIC Is A MACHINIST TOOL that has been Proven Over and Over again during our 36 Years in Business as the Best Way to Permanently Mark Anything Metal.          

Here Are Etch-O-Matic Machinist Tool Kits That Are
Combined With The New STENCIL-MAKERS For
SPECIAL COMBO OFFERS YOU MUST SEE!

With Prices Starting As Low As $79.95
No One Bests These Prices!

Click Below To See The Complete Etch-O-Matic Line
Of Makers (On Special Today) And All Our Popular Kits
Along With TODAY'S SPECIAL PRICES!

CLICK HERE FOR MAIN PAGE!

To Contact Us Just Call: 800-775-0797 During Pacific Coast
 Time From 8:00 A.M. To 4:30 P.M. And A Real Person Will Talk With You
And Explain Anything You Want To Know. 
Email Us Or FAX At 1-360-985-2996

P.O. Box 200 / 500 Wilcox Road
Salkum, WA 98582
Email - Click Here

Phone: 1.800.775.0797
Fax: 1.360.985.2996

 

Visit Our Home Page At:
www.martronics-corporation.com